大涡模拟Smagorinsky模型用于磨粒流精密加工喷嘴的质量控制研究

为研究固液两相磨粒流加工喷嘴小孔过程中的流场分布、涡旋形成规律及涡旋的存在对磨粒流加工的影响机制，采用Smagorinsky亚格子模型对磨粒流加工喷嘴小孔的流道进行大涡数值模拟，并使用磨粒流对变直径喷嘴工件进行加工试验。数值模拟发现磨粒流流体中磨粒与壁面的碰撞与剪切作用随流体的速度增大而增大，同一截面的速度存在速度差，其中还伴随涡旋的存在；通过试验研究发现：经固液两相磨粒流加工后的喷嘴小孔表面质量得到明显提高，喷嘴经过四次不同入口速度的磨粒流加工后大孔处表面粗糙度Ra由1.24 μm降至0.542 μm，小孔处表面粗糙度Ra由1.21 μm降至0.437 μm。结论显示固液两相磨粒流加工技术可有效提高被加工喷嘴工件的内表面质量，加工时同一截面的速度存在速度差，速度差的存在利于涡旋的形成，涡旋的存在利于提高磨粒流加工过程的剪切作用，有助于获得高质量的喷嘴小孔内通道表面。     

Suppression of forced vibration due to chip segmentation in ultrasonic elliptical vibration cutting of titanium alloy Ti–6Al–4V

Ultrasonic elliptical vibration cutting of titanium alloy Ti–6Al–4V is investigated in this research. Because products made of Ti–6Al–4V alloy are usually designed for possessing low-rigidity structures or good-quality cut surfaces, machining requirements such as low cutting forces and slow rate of tool wear need to be fulfilled for realization of their precision machining. Therefore, the ultrasonic elliptical vibration cutting is applied as a novel machining method for those products. Machinability of Ti–6Al–4V alloy by the ultrasonic elliptical vibration cutting with cemented carbide tools is examined to figure out suitable cutting conditions for precision machining of Ti–6Al–4V alloy. As experimental results, generated chips, cutting forces, and profiles of cut surfaces are indicated. A forced vibration problem occurred due to the segmented chip formation, which is also well-known in the ordinary non-vibration cutting. Therefore, characteristics of the forced vibration due to the chip segmentation are investigated in this research. Through the experiments, it is found that the frequency and magnitude of the forced vibration have relation with the average uncut chip thickness and cutting width. Especially, it is found that the averaging effect can suppress the forced vibration, i.e. the chip segmentation tends to occur randomly over the large cutting width, and hence the force fluctuations with random phases tend to cancel each other as the cutting width increases relatively against the average uncut chip thickness. Based on the investigations, a new practical strategy to suppress the forced vibration due to chip segmentation is proposed and verified. Using the proposed method significantly decreased cutting forces and good quality of surfaces are obtained when the forced vibration is suppressed compared to the ordinary non-vibration cutting results. Therefore, the results suggest that the precision machining can be realized without sacrificing the machining efficiency by increasing the width of cut and decreasing the average uncut chip thickness.     

枞树型核电轮槽精铣刀制造技术优化设计

以枞树型叶根精铣刀为例,阐述了可换硬质合金型线刀体和刀片精铣刀的优化设计、制造工艺、建模及优化设计,进行切削过程加工策略优化和加工过程模拟,设计制造了锥柄专用工装及检测环规、磨削刀片后角专用工装,采用NUMROTO软件编制刀片加工工步。该项目研制的可换刀片精铣刀型线精度完全能达到进口铣刀水平,能满足大部分轮槽与叶根加工对型线精度的要求,可以大幅度节约刀具费用。     

Investigations of geometrical structure and morphology of samples made of hard machinable materials after wire electrical discharge machining and vibro‐abrasive finishing

In this article the results concerned influence of processing conditions of the wire electrical discharge machining and vibro‐abrasive machining on the surface layer and morphology of samples made of hard machinable materials used in aircraft industry like: Titanium 5553 β, Inconel 617, Hastelloy X and Magnesium AZ31 have been presented. For this purpose the cubic and cylindrical samples made of hard machinable alloys have been prepared using optimal electric parameters of wire‐cut electrical discharge machining and finally they have been polished using circular vibratory finishing technology and different ceramic shaped stones.     

Wire electrical discharge machinable SiC with GNPs and GO as the electrically conducting filler

SiC based composites filled with graphene nano-platelets (GNPs) or graphene oxide (GO) prepared by rapid hot-pressing exhibit sufficient electrical conductivity for their machinability by wire electro-discharge machining (WEDM). Composites microstructure anisotropy caused by graphene alignment as a consequence of rapid hot pressing was confirmed by measuring of electrical conductivity and thermal diffusivity. Electrical conductivity increased significantly with increased weight fraction of graphene in both measured directions. Highest value of 2031 S/m was obtained for composites with 15 wt. % of GNPs in parallel direction and only 1246 S/m in perpendicular direction to aligned GNPs. Thermal diffusivity is 63.3 mm²/s in parallel and only 23.3 mm²/s in perpendicular direction. The increase of the electrical conductivity has resulted in successful WEDM. The MRR was almost doubled when the filler concentration increased from 5 wt. % GNPs/GO to 15 wt. % GNPs. At the same time, the surface roughness decreased.     

ZnSe/CoSe/NCDPH composites as anode materials for lithium ion batteries with high capacity and long cycle

In this paper, dopamine hydrochloride (DPH) is introduced to synthesize ZIF-8@ZIF-67@DPH in the preparation of ZIF-8@ZIF-67. ZnSe/CoSe/NC_DPH (N-doped carbon) composites are calcined in a high-temperature inert atmosphere with ZIF-8@ZIF-67@DPH as the precursor, selenium powder as the selenium source. ZnSe/CoSe/NC_DPH has high discharge specific capacity, good cycle stability and outstanding rate performance. The first discharge capacity of ZnSe/CoSe/NC_DPH is 1616.6 mAh g⁻¹ at the current density of 0.1 A g⁻¹, and the reversible capacity remains at 1214.2 mAh g⁻¹ after 100 cycles, the reversible capacity is 416.7 mAh g⁻¹ after 1000 cycles at 1 A g⁻¹. Therefore, ZnSe/CoSe/NC_DPH composites provide a new step for the research and synthesis of new stable, high-capacity, and safe high-performance lithium ion batteries. The bimetallic selenide composites not only have bimetallic active sites, but also can form synergistic effect between different metal phases, which can effectively reduce the capacity attenuation caused by volume expansion and reactive stress enrichment during lithium storage of metal oxide anode materials. Meanwhile, N-doped carbon can improve the conductivity and provide more active sites to store lithium, thus improving its lithium storage capacity.     

Suppression of diamond tool wear in machining of tungsten carbide by combining ultrasonic vibration and electrochemical processing

As an important ceramic material, tungsten carbide (WC) is utilized as the typical mold in precision glass molding, which has replaced conventional grinding and polishing to provide a highly replicative process for mass manufacturing of optical glass components. Ultra-precision grinding, which is time consuming and has low reproducibility, is the only method to machine such WC molds to high profile accuracy. Although diamond turning is the most widely used machining method for fabrication of optical molds made of metals, diamond turning of WC is still considered challenging due to fast abrasive wear of the diamond tool caused by high brittleness and hardness of WC. Ultrasonic vibration cutting has been proven to be helpful in realizing ductile-mode machining of brittle materials, but its tool life is still not long enough to be utilized in practical diamond turning of optical WC molds. In the current study, a hybrid method is proposed to combine electrochemical processing of WC workpiece surface into the diamond turning process. Cutting tests on WC using poly-crystalline diamond tools were conducted to evaluate its effect on improvement of tool wear and surface quality. Validation cutting tests using single crystal diamond tools has proven that the proposed hybrid method is able to significantly reduce the diamond tool wear and improve the surface quality of machined ultra-fine grain WC workpiece compared to ultrasonic vibration cutting without electrochemical processing.     

Processing capabilities of micro ultrasonic machining for hard and brittle materials: SPH analysis and experimental verification

Micro ultrasonic machining (micro-USM) is an unconventional micromachining technology that has capability to fabricate high aspect ratio micro-holes, intricate shapes and features on various hard and brittle materials. The material removal in USM is based on brittle fracture of work materials. The mechanical properties and fracture behaviour are different for varied hard and brittle materials, which would make a big difference in the processing capability of micro-USM. To study the processing capability of USM and exploit its potential, the material removal of work materials, wear of abrasive particles and wear of machining tools in USM of three typical hard and brittle materials including float glass, alumina, and silicon carbide were investigated in this work. Both smoothed particle hydrodynamics (SPH) simulations and verification experiments were conducted. The material removal rate is found to decrease in the order of glass, alumina, and silicon carbide, which can be well explained by the simulation results that cracking of glass is faster and larger compared to the other materials. Correspondingly, the tool wear rate also dropped significantly thanks to the faster material removal, and a formation of concavity on the tool tip center due to intensive wear was prevented. The SPH model is proved useful for studying USM of different hard and brittle materials, and capable of predicting the machining performance.     

一种大型复杂构件加工新模式及新装备探讨

大型复杂构件是航空航天、能源、船舶等领域装备的核心结构件，此类构件通常具有尺寸大、形状复杂、刚性弱等特点。传统“分体离线加工-在线检测”模式存在工艺不稳定、过程复杂、柔性差、周期长等问题，以龙门式多轴数控机床加工为代表的“包容式”加工模式，难以适应大型复杂构件的高效高质量加工制造需求。提出一种基于移动式和吸附式机器人的多机协同原位加工新模式，通过多机器人系统自主寻位、精确定位加工与加工质量原位检测，实现大型复杂构件多安装面并行铣削、制孔与打磨等作业。多机器人系统包括移动式混联机器人、吸附式并联机器人、移动式串联铣削机器人、移动式双臂加工机器人和移动式打磨机器人。构建多机协同原位加工模式，需要揭示多机器人协同原位加工行为与大型弱刚性结构件质量控制的交互机理，面临着本体、测量、工艺和集成四个方面的挑战，需要设计高灵活、高刚度的移动式和吸附式加工机器人，解决移动机器人自主准确寻位和超大结构件原位高精检测难题，攻克加工变形误差在线补偿和振动抑制技术，通过集成实现多机协同高效高精加工，为大型复杂构件的高效高质量制造提供创新技术及装备，并实现此类构件制造核心技术及装备自主可控。     

基于修正等速运动规律的自由曲面多轴加工刀轴序列优化方法

针对自由曲面多轴加工中起始位置处刀具相对工件速度、加速度不为零导致的一定程度刚性冲击现象,提出了一种基于修正等速运动规律的刀轴序列优化方法,通过控制工件坐标系中决定刀具姿态的两个约束角,使之变化遵循修正等速运动规律,获得了切削行上平稳变化的刀轴序列,避免了由于起始位置处刀具相对工件速度、加速度不为零导致刀具不能精准到达后续加工位置的现象。算例分析表明,该方法能产生平稳且光滑的刀轴序列,可一定程度改善机床运动性能,提高加工表面质量。